Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - Tomasz

Pages: [1]

PyroSim / Re: Convert from dwg

« on: February 17, 2022, 01:11:08 pm »

Witam
Dzi?kuj? za odpowied? i sugesti?
Tak te? robi?em , pomimo zaznaczenia aby podczas konwersji podk?ad znalaz? si? na pocz?tku uk?adu wspó?prz?dnych nic to nie dawa?o
Pobawi?em si? jeszcze i znalaz?em sposób otóz :
- otworzy?em podk?ad w GSTARCAD i pousuwa?em niepotrzebne warstwy
- dopiero tak oczyszczony podk?ad po konwersji by? widziany w PYROSIM

Jeszcze raz dzi?kuj? i pozdrawiam jednocze?nie zamykaj?c w?tek

PyroSim / Convert from dwg

« on: February 09, 2022, 12:28:50 pm »

Hello
When converting a dwg file, I only see its name in the project tree, but I do not see it in the 2D and / or 3D view
I am asking for help, which I am doing incorrectly

PyroSim / Re: Meshing Problem

« on: October 21, 2021, 03:17:49 am »

In such a situation, I simply counted all the valves one by one - in the project tree - and then I tracked which valve was the problem

PyroSim / Multi-level object

« on: October 21, 2021, 03:08:46 am »

I have been working for PYROSIM for some time but I have a problem with multi-level models.
I am asking for tips on how to start drawing a multi-level object.
What is the BACKGROUND IMAGE for a given floor?.

I will be grateful for any hints and tips

PyroSim / Can't open result

« on: August 15, 2021, 05:27:56 am »

Hello
In a new project while the simulation is running correctly the next steps are counted and I can run the resukts using both SHOWS RESULTSbutton during the simulation and after it has been stopped where I already have calculations for 100s
I am asking for tips what is wrong

PyroSim / Re: Isosufrace

« on: November 13, 2020, 12:59:04 am »

Hello

Thank you for your answer
I'll run the model and see how it behaves

Thanks again
Best regards

PyroSim / Isosufrace

« on: November 05, 2020, 04:59:15 am »

Hello
I,m beginner in PYROSIM
What can I get by selecting 10m Visibility in the isosurfaces menu?
What such results will show me .

PyroSim / Perforation

« on: July 20, 2020, 09:31:44 am »

Hello

How can I model a perforated sheet in PYROSIM?
I will be grateful for any suggestions
Is it possible to download and where from additional libraries for surfaces and materials?

Best regards

PyroSim / damper setting at 40 degrees of opening

« on: July 09, 2020, 01:23:12 am »

Hello

I have very important question
How to model the damper so that it opens 40 degrees during the simulation ?
I will be grateful for any hints

PyroSim / Re: set up sprinkler in pyrosim

« on: January 11, 2020, 12:36:51 pm »

Witam
Ustaw warunki kiedy ma wystartowa? zraszacz

PyroSim / Widok Geometria PYROSIM

« on: August 21, 2019, 11:56:48 am »

Hello

I dont have option PYROSIM VIEW when I want watch results after calculation.
Please help me where is problem .

Best regards
Tomasz